Racing clutch pricing

1. Dsg Clutch Replacement
2. Dsg Clutch Tool
3. Dsg Clutch Pack Upgrade
4. Dsg Clutch Replacement Cost
5. Dsg Clutch Pack Replacement Cost
6. Dsg Clutch Operation On Audi A3 2010
7. Dsg Clutch Slipping

These prices are valid for TVS Engineering/DSG Dokter in the Netherlands. Contact your local Dealer for the prices in your region.

• Dsg clutch and flywheel. Tdi-man; Apr 14, 2014; Replies 0 Views 331. REPLACEMENT CLUTCH? COSTS AND ADVICE? Ogginater; Feb 4, 2013; Replies 3.
• The dual-clutch transmission, also known as the Direct Shift Gearbox (DSG) or twin-clutch transmission, is an automated transmission that can change gears faster than any other geared transmission.

TVS DSG Racing clutches are designed to increase clutch torque capacity to the maximum without sacrificing reliability or drivability. To achieve this we carefully balanced the friction surface area, friction materials, plate designs and clutch pack shimming.

General Information about this Transmission can be found in the Wikipedia entry. Additional information can be found in the Official Factory Repair Information and sources such as Bentley Publisher's VW SSP (Self-Study Program 851403) and Bentley Publisher's Audi SSP (Self-Study Program 951403).

Coding

• When replacing this Mechatronic unit, simply copy the coding from the original Auto-Scan and paste it into the New Coding section of the replacement followed by clicking [Do it!].
  
• If the original Coding is unknown, coding information can be found in the pop-up balloon within the VCDS [Coding-07] function.
  

Basic Setting

Prerequisites:

• Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. (Fluid Level needs to be correct!)
• Selector Lever in P
• Ignition ON
• Engine ON (Idling) for one minute or more
• Brake Pedal operated (hold for the whole procedure)
• Throttle Pedal not operated
• Cruise control is switched OFF
  

NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.

[Select]
[02 - Transmission]
[Basic Settings - 04]

Dsg Clutch Replacement

Transmission Tolerances (Engaged Calibration)

Group 061
[Go!]

• When you go to Basic Settings 061 and click GO the screen may look like this: Basic Settings 061
  
• Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 061
  

Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.

Transmission Tolerances (Synch. Point. Measurement)

Group 060
[Go!]

• When you go to Basic Settings 060 and click GO the screen may look like this: Basic Settings 060
  
• Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 060
  

Wait until Basic Settings has switched to ON and all numbers have stopped moving.

Clutch Adaptation

Control Module Software Version < 0800:

Dsg Clutch Tool

Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Special notes.

• When found in the early software level (0627/0628) (8N) Audi TT:
  • Basic Settings group 062 may take several minutes to complete. The final values may report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished.
  • If Basic Settings group 062 reports ERROR:| Group 062| Not | Available try test driving the vehicle and repeating at normal operating temp.

Internal Ref: ST?ID=66725 and E?ID=309867

Control Module Software Version >= 0800 :

Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Clutch Safety Function)

Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Pressure Adaptation)

Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Steering Wheel Paddle Installation)

Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (ESP & Tip Cruise Control Installation)

Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

[Done, Go Back]
Switch off Ignition, wait 10 Seconds and switch it back on.
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.

Dsg Clutch Pack Upgrade

Special Procedures

Dsg Clutch Replacement Cost

Defined Test Drive

Suggested test drive after replacing the mechatronic or successful basic setting.
Prerequisites:

• Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
• Do Not use Cruise Control.

Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive, Not Tiptronic Mode.
Evaluate creep and starting-off points.
Check for leaks.

NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.

Special Notes

• Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own.

• It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises.

Dsg Clutch Pack Replacement Cost

• Customers with TDI's have reported that an RPM range of 2000-2500 rpm is sufficient.

Dsg Clutch Operation On Audi A3 2010

Replacement

Replacement Mechatronic units should be ordered by VIN based on PR Codes to confirm vehicle compatibility.

Dsg Clutch Slipping

• Run and save a complete Auto-Scan and save it prior to Mechatronic unit removal. See the Online Manual Auto-Scan.
  
• Enter the original Coding into the New Coding section of the replacement controller.
• Complete Basic Settings
• Complete the Defined Test Drive